新邱盆式新邱橡膠支座下面應設置支承墊石，支承墊石混凝土強度等級不宜低于C40.墊石高度應考慮 支座裝置、維護和替換的方便。支承墊石及墩頂混凝土應該按JTG D62-2004的局部承壓部件要求裝備相應的鋼筋網。墩臺頂面需按錨固套筒規格、數量預留栓孔。預留栓孔的直徑和深度大于套筒直徑和長度50mm~60mm,中心誤差不該超過10mm。

　　新邱盆式新邱橡膠支座運輸到現場后，應該開箱檢查支座各部分零件及裝箱單，檢查合格后再放入包裝箱，裝置時再開箱。活動支座在開箱后應該留意對聚四氟乙烯板和不銹鋼冷軋鋼板的保護，避免劃傷或許有贓物附著在乙烯板和冷軋鋼板的表面，而且檢查5201-2硅脂是否注滿。

　　盆式新邱橡膠支座裝置時，支承墊石頂面應該鑿毛，并用清水沖去墊石上面的雜物，待墊石表面枯燥后，在錨固螺栓孔位置以外的支承墊石頂面涂滿環氧砂漿調平層，支座就位后、對中并調整水平后，用墊塊將支座墊起。

　　用環氧砂漿或強度等級較高的砂漿灌注套筒周圍空隙及支座底板四周未填滿環氧砂漿的位置，而且將砂漿搗實，完工后應該將支座底板以外溢出的砂漿清理干凈，砂漿硬化后再拆去支座墊塊。