板式豐城橡膠支座的安裝及安裝過后的檢查公路橋梁板式豐城橡膠支座按照支座的形狀可以分為矩形板式豐城橡膠支座GJZ和圓形板式豐城橡膠支座GYZ。四氟板滑動矩形板式橡膠支座 GJZF4，和四氟板活動圓形板式橡膠支座GYZF4。矩形圓形板式支座適合安裝在彎橋，坡橋，斜橋，寬橋中，安裝時當出現坡度大于1%時要采用預埋鋼板和混凝土墊塊將梁底調平。四氟板活動支座要水平安裝，設置上下鋼板。

　　1、板式橡膠支座安裝設置墊石墊石的長度和寬度要比支座的尺寸增加50mm左右，高度為100mm以上，便于梁體頂升時千斤頂的安裝。墊石內置鋼筋，便面平 整，清潔，干爽，保持高度誤差。

　　2、板式橡膠支座安裝落梁 檢查支座，標出中心線，安裝不得出現脫空現象。

　　3、板式橡膠支座安裝注意事項 同一根梁上不宜設置兩個或者多個支座。不同規格的支座不能并排安置。

　　4、板式橡膠支座安裝過后的檢查 安裝過后檢查時候漏放，四氟板滑動支座是否注入硅脂。圓形板式橡膠支座和矩形板式橡膠支座的安裝過程中需要用水泥砂漿進行調高，保持支撐墊石的高度一致，板式橡膠支座在架梁落梁時要保持平穩，防止支座的壓偏或支座產生初始剪切變形。