古晨工程橡膠提示您充氣芯模充氣時應該注意什么？
來源：古晨工程橡膠發布時間：2020-10-02瀏覽次數：83602 次
在充氣芯模就位后，打開進氣閥門，用空壓機充氣。充氣時用壓力表操控監測氣壓，充氣芯模充氣壓力通常為0.027 MPa（但得對具體型號為充氣壓力）。當氣壓到達運用壓力時，將氣閥封閉，停止充氣。
充氣芯模充氣時應該注意什么
(1) 在充氣芯模就位后，打開進氣閥門，用空壓機充氣。充氣時用壓力表操控監測氣壓，
充氣芯模充氣壓力通常為0.027 MPa（但得對具體型號為充氣壓力）。當氣壓到達運用壓力
時，將氣閥封閉，停止充氣。
(2 )充氣芯模充氣時留意不得超壓。
(3) 充氣芯模初次運用前應試充氣，測定每套到達運用壓力時的充沛時刻，依據混凝土的
初凝時刻斷定所需空壓機的數量，以確保板梁豎肋及上部混凝土在其下部混凝土初凝前開端
澆注，防止造成施工縫，然后確保每片板梁混凝土的整體性。
經現場測驗，用6m3/min的空壓機充氣，每套充氣芯模充氣時刻為15～20min，所需時刻
較短，對混凝土施工縫的構成影響較小。
